Posted on February 26, 2019


This instruction manual describes preventive maintenance and quick FANUC SYSTEM 3T-MODEL C is designated to be assembled inside an NC machine. Fanuc System 3T-Model D Operator’s Manual(BE 02) – Free download as PDF File .pdf) or read online for free. I am looking for an operators manual for a Fanuc 3 T controller used on a small Wasino gang lathe. Any help would be appreciated. Going to.

Author: Moogugami Kagabei
Country: Romania
Language: English (Spanish)
Genre: Art
Published (Last): 21 October 2015
Pages: 288
PDF File Size: 11.69 Mb
ePub File Size: 6.36 Mb
ISBN: 744-9-74820-937-5
Downloads: 26008
Price: Free* [*Free Regsitration Required]
Uploader: Yozshushura

Fanuc 3t Maintenance Manual

The time now is Tsugami Resto Great looking job. Mine has serial so they’re probably real close!

Thank you that would be very helpful as the photo of the param. And that zero is relative to the location of the table at poweron, not relative to the absolute machine zero. You must set the tools using G50’s. Tags for this Threadmahual centerssinceuseful.

Fanuc 3T operator manual

Need help understanding “zero” on a Fanuc 3T. The time now is This is probably exposing my ignorance, but gridshift is the only thing I can find that references the machine absolute zero.

Last edited by fordav11; at What did they use originally? The ballscrews were actually fresh and the table had no appreciable backlash less than a tenth of a thou.

Anybody know if thats an option you can add afterwards? But all of the information I can find seems to imply that its only used after major operations like replacing the servo or ballscrew and where you need to realign turrets and such. While you do not have a parameter manual you can see if you have those parameters. Now from what can see, Tsugami may not have made the actual spindle.


I’ve cut a couple things on it since the G50 discovery, the first cut was this buffer. The parameter descriptions are in the back of a Fanuc System 3T operator manual.

Fanuc 3t Manuals

I have the communications working for uploading and downloading prorgams, but drip would be really nice. Look’s like you have a Hydro unit I don’t have for the draw bar. By roymanvega in forum Fanuc. Program input is not started with the faunc input external start signal MINP. MINP isn’t defined anywhere in the maintennace manual or the electrical manual.

Need help understanding “zero” on a Fanuc 3T.

Last edited by Kevin Taylor; at It’s taken about 6 months to get it danuc operational, and now I’m ready to make its first cuts since it was torn apart and rebuilt.

There are some advanced tricks to avoid re-setting G50’s for each job but start with this simple method first. Let me know if I can help with what documation I have.

I need some help setting tool offsets when I get up and running again Thank’s Kevin. You will need it several times. Results 1 to 10 of Anybody has any idea what that means?


I’m sure nearly any program that your old machine can handle will fit in the available memory. I’m not an expert at reading these things, but it looks like this machine has 8K of memory? Thanks fomaz, I already have the original yellow floppy maintenance manual which theoretically describes all of the “non-option” parameters. I have a Fanuc 3T Maintenance manual but nothing Tsugami specific, Fanuc referred me to Tsugami, and those guys told me to talk to Remington Sales who disavowed all knowledge of this unit.

How mqnual I make sure my tool offsets are correct the second time I power-on on a lathe?

Ad text and spelling. Program input is started with the data input external start signal MINP. Manyal 1 of 2 1 2 Last Jump to page: Did you do a number on the DC servo’s? For anyone else in the future who has the same question, I took fordav11’s solution and implemented it like this. From my admittedly limited understanding, I have the absolute zero which I can tweak with gridshift offsets, but does not seem to be used for anything except G28, e.