E Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials force~ notched specimens~ unnotched. ASTM E()e1 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials. Last previous edition approved in as E – 96()?1. DOI: / E 2 Handbook of Fatigue Testing, ASTM STP
|Country:||Papua New Guinea|
|Published (Last):||18 March 2012|
|PDF File Size:||11.83 Mb|
|ePub File Size:||13.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
Unmanned Maritime Vehicle Standards. Fatigue Standards and Fracture Standards. This entire procedure should be clearly explained in the reporting since it is known atm in? Otherwise, astj same dimensional relationships should apply, as in the case of the specimens described in 5. E – 15 See all versions Redline Version E The results may also e466-69 used as a guide for the selection of metallic materials for service under conditions of repeated direct stress.
Ra, in the longitudinal direction. E e1 E E E E – 85 See all versions E e1 E E Consumer Product Evaluation Standards. NOTE 2—Measurements of dimensions presume smooth surface?
Redline Version Ee1 E Regardless of the machining, grinding, or polishing method used, the? Soap Standards and Polish Standards. Durability of Nonmetallic Material Standards. Fatigue Standards and Fracture Standards ASTM’s fatigue and fracture standards provide the appropriate procedures for carrying out fatigue, fracture, and other related tests on specified materials.
Fatigue Standards and Fracture Standards
No further reproductions authorized. Paper Standards and Packaging Standards.
In the typical regime of 10? One set of strain gages should be placed at the center of the gage length to detect misalignment that causes relative rotation of the specimen ends about axes perpendicular to the specimen axis.
There was a problem providing the content you requested
It is beyond the scope of Practice E to extrapolate beyond this range or to extend this assumption to other materials systems that may be viscoelastic or viscoplastic at ambient test temperatures and within the frequency regime mentioned. E – 02 e1 See all versions E e1 E E E — 07 FIG. It is important that the accuracy of alignment be kept consistent from specimen to specimen.
Thus, when embarking on a program of this nature it is essential to define and maintain consistency a priori, as many variables as reasonably possible, with as much economy as prudent. For specimens that are less than 0. Also, Refsalthough they pertain to straincontrolled testing, may prove of interest since they deal with sheet specimens approximately 0.
Historical Version s – view previous versions of standard.
Since however, the environment can greatly in? Ee1 E e2 E e1 E E This practice is not intended for application in axial fatigue tests of components or parts. Last previous edition approved in as E — 96 ? One exception may be r466-96 these parameters are under study.
E E E Fire Standards and Flammability Standards. A number in parentheses indicates the year of last reapproval.
ASTM E Conducting Force Controlled Constant Amplitude Axial Fatigue Tests_百度文库
In reporting the results, state the criterion selected for de? Fillet undercutting can be readily determined by inspection. In addition to fracture atm and strain gradient, these standards also present the procedures for determining K-R curves, stress-life and strain-life fatigue data, threshold stress intensity factors, and reference temperatures.
The trial test specimen should be turned about its axis, installed, and checked for each of four orientations within the? Medical Device Standards and Implant Standards. Failure may be de? These tests are conducted to asym and evaluate the behavior, susceptibility, and extent of resistance of certain materials to sharp-notch tension, tear, axial fatigue, strain-controlled fatigue, surface crack tension, creep crack, and residual strain.
The test section length should be approximately two w466-96 three times the test section diameter. Industrial Hygiene Standards and Safety Standards. The test forces should be monitored continuously in the early stage of the test and periodically, thereafter, to ensure that the desired force cycle is maintained. E – 10 See all versions E Individual reprints single or multiple copies of this standard may be obtained e66-96 contacting ASTM at the above address or at phonefaxor service astm.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Every effort should be made to prevent the occurrence of misalignment, either due to twist rotation of the gripsor to a displacement in their axes of symmetry. Ee1 E Ee1 E If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
However, regardless of the nature of the forcing function, it should be reported sine, ramp, saw tooth, etc. These fatigue and fracture standards are useful to manufacturers and other users concerned with such materials in understanding their failure and stability mechanisms.
ASTM International takes no position respecting the 4e66-96 of any patent rights asserted in connection with any item mentioned in this standard.